Switch D-Link DGS-1210-24P PoE jak uruchomic
-
- Wtajemniczony
- Posty: 199
- Rejestracja: ndz cze 09, 2019 4:41 pm
Switch D-Link DGS-1210-24P PoE jak uruchomic
Panowie zakupilem DGS-1210-24P z D-Link, posiada on PoE, czy mozecie mi napisac w jaki sposob ustawic zeby bylo to aktywne. Zakupilem telefon Yealink SIP-T58A, ktory moze byc zasilany wlasnie przez kabel LAN z PoE.
-
- Godfather
- Posty: 1305
- Rejestracja: wt gru 15, 2015 12:19 pm
- Lokalizacja: Żyrardów
Re: Switch D-Link DGS-1210-24P PoE jak uruchomic
Z tego co widzę to switch zarządzalny. Po podłączeniu do sieci dostanie adres IP. Logujesz się na niego przy pomocy przeglądarki i definiujesz które porty są POE.
Trzeba uważać by nie podpiąć do takiego portu urządzenia które nie obsługuje tego standardu zasilania.
Trzeba uważać by nie podpiąć do takiego portu urządzenia które nie obsługuje tego standardu zasilania.
Administratorzy dzielą się na tych, którzy robią kopie zapasowe i tych, którzy będą je robili.
Serwery NAS:
Synology DS211j, DS1511+, RS2212RP+ DS1513+
"Zasłanianie się dysleksją, to jak chwalenie się małym fiu...."- by Pati
gg 2101676
Serwery NAS:
Synology DS211j, DS1511+, RS2212RP+ DS1513+
"Zasłanianie się dysleksją, to jak chwalenie się małym fiu...."- by Pati
gg 2101676
-
- Trochę Wie
- Posty: 113
- Rejestracja: czw sty 17, 2019 9:03 pm
- Lokalizacja: Trier
Re: Switch D-Link DGS-1210-24P PoE jak uruchomic
Login Web-based Management
In order to login and configure the switch via an Ethernet connection, the PC must have an IP address in the
same subnet as the switch. For example, if the switch has an IP address of 10.90.90.90, the PC should have
an IP address of 10.x.y.z (where x/y is a number between 0 ~ 254 and z is a number between 1 ~ 254), and
a subnet mask of 255.0.0.0. There are two ways to launch the Web-based Management, you may either click
the Web Access button at the top of the SmartConsole Utility or open the web browser and enter 10.90.90.90
(the factory-default IP address) in the address bar. Then press <Enter>.
In order to login and configure the switch via an Ethernet connection, the PC must have an IP address in the
same subnet as the switch. For example, if the switch has an IP address of 10.90.90.90, the PC should have
an IP address of 10.x.y.z (where x/y is a number between 0 ~ 254 and z is a number between 1 ~ 254), and
a subnet mask of 255.0.0.0. There are two ways to launch the Web-based Management, you may either click
the Web Access button at the top of the SmartConsole Utility or open the web browser and enter 10.90.90.90
(the factory-default IP address) in the address bar. Then press <Enter>.
DS1621+ / 4x WDRed 4TB
DS214/2xWDRed 4TB
APC Back-UPS PRO 900
APC Back-UPS 950
DS214/2xWDRed 4TB
APC Back-UPS PRO 900
APC Back-UPS 950