Wczoraj (dzień po zakutalizowaniu systemu DSM do Update 6) miałem niemiły incydent. Drugi dysk padł i nie da się go podmontować (poniżej logi dmesg). Może ktoś rzuci okiem i podpowie czy to wina dysku czy może samego urządzenia Synology (DS215j)?
Kod: Zaznacz cały
[ 4.679152] Loading iSCSI transport class v2.0-870.
[ 4.685117] sata_mv sata_mv.0: version 1.28
[ 4.685246] sata_mv sata_mv.0: slots 32 ports 2
[ 4.692179] scsi0 : sata_mv
[ 4.695489] scsi1 : sata_mv
[ 4.699021] ata1: SATA max UDMA/133 irq 58
[ 4.703143] ata2: SATA max UDMA/133 irq 58
[ 12.525520] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 12.705475] ata1.00: ATA-9: WDC WD20EFRX-68EUZN0, 82.00A82, max UDMA/133
[ 12.712214] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 12.735617] ata1.00: configured for UDMA/133
[ 12.755485] scsi 0:0:0:0: Direct-Access WDC WD20EFRX-68EUZN0 82.0 PQ: 0 ANSI: 5
[ 12.765166] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 12.772970] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 12.778385] sd 0:0:0:0: [sda] Write Protect is off
[ 12.783205] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 12.783271] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.821251] sda: sda1 sda2 sda3 < sda5 >
[ 12.826888] sd 0:0:0:0: [sda] Attached SCSI disk
[ 15.765919] Delay 5 seconds to wait for disk 2 ready.
[ 26.300385] ata2: link is slow to respond, please be patient (ready=0)
[ 30.798719] ata2: SRST failed (errno=-16)
[ 30.802750] ata2: SRST fail, set srst fail flag
[ 36.346667] ata2: link is slow to respond, please be patient (ready=0)
[ 40.845004] ata2: SRST failed (errno=-16)
[ 40.849034] ata2: SRST fail, set srst fail flag
[ 46.392953] ata2: link is slow to respond, please be patient (ready=0)
[ 75.842068] ata2: SRST failed (errno=-16)
[ 75.846099] ata2: SRST fail, set srst fail flag
[ 75.850653] ata2: limiting SATA link speed to 1.5 Gbps
[ 80.860212] ata2: SRST failed (errno=-16)
[ 80.864242] ata2: SRST fail, set srst fail flag
[ 80.868798] ata2: reset failed, giving up
[ 80.872834] ata2: get error flags 0x1
[ 80.876527] ata2: do detect tries 1
[ 80.880038] ata2: device plugged sstatus 0x123
[ 80.884522] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xf t1
[ 80.891088] ata2: edma_err_cause=00000000 pp_flags=00000000, dev connect
[ 80.897837] ata2: hard resetting link
[ 86.848000] ata2: link is slow to respond, please be patient (ready=0)
[ 90.926492] ata2: SRST failed (errno=-16)
[ 90.930521] ata2: SRST fail, set srst fail flag
[ 90.935075] ata2: hard resetting link
[ 96.884289] ata2: link is slow to respond, please be patient (ready=0)
[ 100.962781] ata2: SRST failed (errno=-16)
[ 100.966812] ata2: SRST fail, set srst fail flag
[ 100.971365] ata2: hard resetting link
[ 106.920579] ata2: link is slow to respond, please be patient (ready=0)
[ 136.009828] ata2: SRST failed (errno=-16)
[ 136.013857] ata2: SRST fail, set srst fail flag
[ 136.018412] ata2: limiting SATA link speed to 1.5 Gbps
[ 136.023582] ata2: hard resetting link
[ 141.067957] ata2: SRST failed (errno=-16)
[ 141.071986] ata2: SRST fail, set srst fail flag
[ 141.076540] ata2: reset failed, giving up
[ 141.080574] ata2: get error flags 0x1
[ 141.084259] ata2: do deep tries 1
[ 148.075380] ata2: get error flags 0x1
[ 148.079065] ata2: EH complete